The Aruba-3 Series (AWI) residential, cast iron, hot water boiler is a fully-packaged, installer-ready product. The integral draft diverter provides a low profile design allowing the boiler to be installed in areas requiring a low clearance. This atmospheric, gas-fired boiler is for use with a conventional chimney. The Aruba-3 Series is packaged with the option of either natural or LP gas as well as a choice of a standing pilot or electronic ignition system.

Additionally, the Aruba-3 features a standardized Honeywell operating control with the unique option for placement on the right, left or top to accommodate any boiler room design.

The Bali Series (BWF) residential, cast iron, hot water boiler is a fully-packaged, installer-ready product. An integral fan permits venting directly through a wall. With the addition of a Category-1 Vent Kit, the Bali has the option of venting into some chimneys that are too small to vent an atmospheric boiler of the same input. The Bali Series is packaged with an electronic ignition system and has the option of either natural or LP gas.

The Bermuda Series (BSI) residential/light commercial, cast iron, steam boiler is a fully-packaged, installer-ready product. The integral draft diverter provides a low profile design allowing the boiler to be installed in areas requiring a low clearance. This atmospheric, gas-fired boiler is for use with a conventional chimney. The Bermuda Series also comes standard with a probe-type low water cut-off safety control. The Bermuda Series is packaged with the option of either natural or LP gas as well as a choice of a standing pilot or electronic ignition system.

The heat exchangers are built with steel push nipples below the water line where superior strength and resistance to expansion and contraction is important. Cast iron push nipples above the water line are larger than often found on similar units to provide optimum steam quality.

The Bimini (BWC) Series boiler is a cast aluminum, high-efficiency, condensing, direct-vent, gas-fired, hot water boiler. There are multiple venting options to suit homeowner and installer preferences. Some models are designed to be wall-mounted for when floor space is at a premium. Each model is ENERGY STAR® qualified.

The BWC is available in both natural and LP gas models. The BWC also includes a microprocessor-based control system. Additional features include direct spark ignition, outdoor reset temperature sensor, domestic hot water priority, pump controls for heating and domestic hot water and a fully modulating burner. The BWC comes fully wired and ready for installation.

The CABO-2 Series (CWD) residential, cast iron, direct-vent, hot water boiler is a fully-packaged, installer-ready product. The Bali Series is packaged with an electronic ignition system and has the option of either natural or LP gas. The Cabo-2 Series control supports priority zoning for an indirect water heater and an optional plug-in outdoor temperature reset control. Each model is ENERGY STAR® qualified.

A cast iron, wet-leg heat exchanger provides efficient heat transfer and reliability over the product's lifetime.

The Cayman Series (CWI) residential/light commercial, cast iron, hot water boiler is a fully-packaged, installer-ready product. The integral draft diverter provides a low profile design allowing the boiler to be installed in areas requiring a low clearance. This atmospheric, gas-fired boiler is for use with a conventional chimney.

The Cayman Series is packaged with the option of either natural or LP gas as well as a choice of a standing pilot or electronic ignition system. The Cayman Series also includes an optional tankless coil for domestic hot water (see specifications) and a larger range of available sizes.

The Maui Series (MWC) boiler is a residential, fully-packaged, installer-ready, copper-finned, gas-fired, hot-water, condensing, direct vent boiler. This 85% efficient, ENERGY STAR® qualified boiler is offered in a "heat only" or "Combi" model that provides both domestic heat and hot water. The Maui is packaged with a concentric polypropylene venting system. The Maui is available in one size at 116,000 BTU/hr in both natural and LP gas.

The Maui's wall-mounted design is ideal for situations where space is at a premium. The Maui boiler utilizes direct spark ignition and is equipped with an expansion tank.

The Freeport CT Series boiler is a fully-packaged, installer-ready, 3-pass cast-iron, oil-fired, hot water boiler. The Freeport CT Series is designed for installation with a standard chimney. This boiler is available in heating capacities from 92,000-286,000 BTU/hr. Some models of the Freeport CT boiler are ENERGY STAR® qualified.

The Freeport CT is available with a Beckett (standard) or Riello oil burner. Features include a 3-pass heat exchanger to maximize heat transfer and ease of service. The Freeport CT Series also includes a cast-iron burner swing door and Honeywell operating controls.

The Freeport ODV Series boiler is a fully-packaged, installer-ready, 3-pass cast-iron, oil-fired, hot water boiler. The Freeport ODV Series is designed for direct venting in homes without a chimney. This boiler is available in heating capacities from 91,000-150,000 BTU/hr heating capacity.

Features include a 3-pass heat exchanger to maximize heat transfer and ease of service. The Freeport ODV series also includes a cast-iron burner swing door, Honeywell operating controls and direct vent package including 15 feet of venting material and a coaxial vent terminal. The ODV-75 is ENERGY STAR® qualified.

The Kingston (KSZ) Series boiler is an installer-ready, residential, cast-iron, oil-fired, steam boiler. The Kingston is designed for installation with a standard chimney. The Kingston is available in heating capacities from 79,000 to 235,000 BTU/hr. This boiler is available in a semi-packaged 'Shorty' version. The 'Shorty' is shipped with the burner and controls separate from the boiler.

Options on the KSZ series include a domestic coil and your choice of three different oil burners: Beckett (standard), Riello or Carlin. Features of the KSZ series include a wet-base heat exchanger design, cast-iron burner swing door, a 3-prong quick disconnect for easy service and a barometric damper. Some models of the KSZ are ENERGY STAR® qualified.

The Tobago (TWZ) Series boiler is an installer-ready, residential, cast-iron, oil-fired, water boiler. The Tobago is designed for installation with a standard chimney and is available in heating capacities from 80,000 to 241,000 BTU/hr. This boiler is available in a semi-packaged 'Shorty' version. The 'Shorty' is shipped with the burner and controls separate from the boiler.

Options on the TWZ series include a domestic coil and your choice of three different oil burners: Beckett (standard), Riello or Carlin. Features of the TWZ series include a wet-base heat exchanger design, cast-iron burner swing door, a 3-prong quick disconnect for easy service, Honeywell operating controls, Taco circulator, and a barometric damper. Some TWZ models are ENERGY STAR® qualified.

The Bimini (BWC) Series boiler is a cast aluminum, high-efficiency, condensing, gas-fired, direct-vent, hot water boiler. There are multiple venting configurations and material options to suit owner and installer preferences. The BWC Commercial is available in firing rates of 300,000 to 425,000 BTU/hr.

The BWC is available in both natural and LP gas. The BWC also includes a microprocessor-based control system. Additional features include direct spark ignition, outdoor reset temperature sensor, domestic hot water priority, pump controls for heating and domestic hot water and a fully modulating burner. The BWC is fully wired and ready for installation.

The FW Series boiler is a 3-pass cast-iron boiler designed for use with light oil, gas, or a light oil-gas combination. The FW Series is designed for installation with either a standard chimney or a pressurized vent system. The boiler has a swing-open front door for easy service and inspection, and the stainless steel baffles are easily removed via the front door.

The FW comes in six sizes, with heating capacities ranging from 355,000 to 1,091,000 BTU/hr. The burner is ordered separately.

The Series 16 is a commercial, cast-iron, gas-fired, hot-water boiler. The Series 16 is designed for use with a conventional chimney. The boiler is packaged with an electronic ignition system and has the option of either natural or LP gas. The Series 16 is available in firing rates from 325,000 to 585,000 BTU/hr.

The Series 16 is shipped as a semi-packaged boiler with the boiler sections, base, and flue collector preassembled; final assembly is then easily completed in the field.

The Series 24 is a cast-iron water or steam boiler designed for use with light oil, gas, or a light oil-gas combination. The Series 24 is designed for installation with either a standard chimney or a pressurized vent system. The boiler has a swing-open front door for easy service and inspection.

The Series 24 is available in 10 sizes, with heating capacities ranging from 342,000 to 1,852,000 BTU/hr.

This boiler is easily assembled with draw rods, and all the maintenance access areas are located on the left side, simplifying servicing.

The Series 32 is a commercial, cast-iron, gas-fired, hot-water or steam boiler. The Series 32 is designed for use with a conventional chimney. The boiler is equipped with an electronic ignition system and is available for use with natural gas. The Series 32 is available in firing rates from 380,000 to 2,850,000 BTU/hr. This boiler has built-in draft hoods for installation under low ceilings, and a choice of control options make the Series 32 the best choice for a wide variety of commercial applications.

Domestic hot water can be provided by an optional tankless coil water heater on water boilers only. The steam boilers are tapped for Mega-Stor or Maxi-Therm indirect water heaters.

The Series 32 has a compact design which uses preassembled and tested base modules. These modules have individual gas trains with a residential style combination gas valve and ignition control for simplicity and redundancy. These base modules are combined to provide the appropriate input.

Heat exchanger sections are shipped unassembled, which makes them easier to handle, get through narrow doorways and assemble.